INSTALL INSTRUCTIONS P-MID-1 w/P-MFK-5
MIDDLE PARTITION w/MOUNTING FILLER PANEL KIT
1997-2008 CHEVROLET/GMC FULL SIZE PASSENGER VANS
TOOLS REQUIRED:
Power drill
Drill bit set
Ratcheting wrench
Standard & Metric socket set
HARDWARE:
QTY DESCRIPTION
PART #
5
6
20
12
8
1
1
2
8
¼” x 1 ½” Hex head Lag Bolt
GSM33062
GSM33060
GSM32000
GSM30023
GSM30016
GSM30017
GSM33015
GSM31006
GSM31014
¼” x 1” Hex head Lag Bolt
¼-20 x ¾” Carriage Bolt
¼-20 Serrated Nut
¼-20 Nylock Nut
5/16-18 Nylock Nut
5/16-18 x 2” Hex Head Bolt
5/16 Flat Washer
¼” x 1” Fender Washer
Upper Center Steel
Filler Panel
Passenger Side
Mounting Bracket
Driver Side Upper
Lexan Filler Panel
Passenger Side Steel
Door Filler Panel
(2-Piece) Driver Side
“B” Pillar Mounting
Bracket
Main Partition
Frame
Driver Side Lower
Steel Filler Panel
serrated nuts.
• Press partition as far forward and mark mounting holes where driver side mounting
bracket and “C-pillar” come in contact.
• Pre-drill 3/16” holes into “C-pillar”.
• Attach bracket to C-pillar using (3) ¼” x 1” Hex head lag bolts.
• Plastic trim panel must be notched around bracket to mount.
3. ATTACH PASSENGER SIDE MOUNTING BRACEKT:
• Press partition as far forward as
possible and holding bracket to
partition (square tubing section)
determine where to slot headliner to
accept mounting bracket.
• Slot headliner and position mounting
bracket to be flush with vehicle inner
roof support.
• Mark (3) mounting holes and pre-
drill using 3/16” drill bit.
5/16-18 x 2”
Hex head bolt
• Attach bracket to vehicle using (3)
¼” x 1” Hex head lag bolts.
• Press partition up to bracket and
mark holes where bracket and
partition come together.
Passenger side upper
mounting bracket
• Drill 5/16” holes on these marks and
bolt partition to bracket using 5/16-
18 x 2” Hex head bolt, washer, and
nylock nut.
4. ATTACH UPPER STEEL CENTER FILLER PANEL:
• Attach upper center filler to partition through the holes pre-drilled at subassembly
using ¼-20 x ¾” Carriage bolts and serrated nuts.
• Tighten all hardware.
P-MID-1^MFK-5_INST_9-07
5. ATTACH DRIVER SIDE UPPER LEXAN FILLER PANEL:
• Position driver side ¼” lexan filler panel to partition so that minimal space is between
the vehicles window, (or window guard) and the lexan filler.
NOTE: It is necessary to keep a 1/8” gap between the window or guard and the filler to allow for
expansion and contraction of the lexan during temperature fluctuations.
• Drill (6) 5/16” holes evenly spaced through both the ¼” lexan filler panel and the
partition frame. Attaching to the frame directly will help to avoid filler rattling.
• Bolt lexan filler to partition using ¼-20 x ¾” carriage bolts and nylock nuts.
6. ATTACH DRIVER SIDE LOWER STEEL FILLER PANEL:
• Position driver side lower aluminum filler panel tight to vehicles interior trim and
floor.
• Using slots in filler panel as a drill guide mark and drill partition using 5/16” drill bit.
• Attach filler panel to partition using ¼-20 x ¾” carriage bolts and serrated nuts.
7. ATTACH PASSENGER SIDE DOOR STEEL FILLER PANEL:
• Position on front row bench in van close side doors.
• Hold filler panel to partition so that it does not interfere door mechanisms.
• Mark and drill 3/16” holes through partition tubing.
• Attach filler to partition using ¼-20 x ¾” Hex head thread cutting bolts.
• Vacuum out all metal shaving and double check door operation.
Lexan
Notched
¼-20 x ¾”
P-MID-1^MFK-5_INST_9-07
|
Briggs Stratton THE POWER WITHIN 600 SERIES User Manual
Brother MFC 7550MC User Manual
Bunn JDF 2 User Manual
Carrier 48HJ004 007 User Manual
Chromalox CAF 6 User Manual
Epson XP 800 User Manual
Gale Banks Engineering Diesel Performance Specialists Automobile Accessories F350 User Manual
Haier HSU18VH7 User Manual
Heat Controller Inc Air Conditioner 10 User Manual
Heat Controller Inc Air Conditioner R 410A User Manual